ACE designs and repairs waterproofing systems in St. George, Utah — below-grade, plaza-deck, split-slab, foundation, and traffic-bearing coatings. We coordinate directly with structural, civil, and landscape so the assembly the contractor bids is the assembly the membrane manufacturer will warrant. Design engagements are priced fixed-fee by phase, and we carry professional liability with limits appropriate to commercial and multifamily work.
Waterproofing is where the water-management strategy of a building either succeeds or generates decades of consequential damage. We design and repair below-grade waterproofing, plaza decks, split-slabs, planters, foundations, and horizontal traffic-bearing systems — coordinating with structural, civil, and landscape designers so the assembly the contractor is asked to build is the assembly the membrane manufacturer will warrant. Explore the ACE waterproofing practice for the full scope of related capabilities we bring to St. George engagements.
St. George sits in a Hot-Dry Desert (Zone 2B Hot-Dry) climate zone. Extreme summer UV and surface temperatures, combined with monsoonal wind-driven rain events, drive envelope decisions toward reflective assemblies, high-heat-tolerant membranes, and expansion-joint detailing sized for a large diurnal thermal swing. Sealants that pass in temperate climates fail here. The St. George building stock we most often work in includes Mojave-adjacent hot-desert exposure and rapid Southern Utah commercial growth. On St. George plaza decks we see repeat failure at planter drain cores, at the drainage-mat termination, and at the wall-to-slab transition — locations where the design detail was correct but the installer sequencing was not. See our Wasatch Front practice for the multi-market context, and Waterproofing Consulting — Salt Lake City for a complementary scope in the same market.
Waterproofing consulting spans three environments — each with different membranes, expected lifespans, and interface details. Failure clusters at transitions between them.
Covering St. George waterproofing design and related scopes
Blindside, positive-side, or bentonite systems designed against soil-side hydrostatic pressure and vapor drive.
Hot-fluid, cold-fluid, or sheet-membrane systems with drainage plane, protection board, insulation, and overburden coordinated as a single assembly.
Perimeter drainage, capillary breaks, and vapor barriers designed against the site-specific groundwater and vapor conditions.
Where an existing assembly is failing, we investigate the mode of failure and design the retrofit — not just re-specify the same membrane.
Review of installer submittals, mock-ups, and field conditions during installation, with continuous QA record for owner and warranty carrier.
Every engagement follows a three-phase delivery structure so you know what you are getting, when.
Below-grade positive-side membrane failure at the wall-to-slab cold joint, plaza-deck failure at planter drain cores, and split-slab failure at the drainage-mat termination — three signature failure modes we investigate repeatedly.
Yes, with limits appropriate to commercial and multifamily projects. Certificates provided on request during the fee proposal.
Damp-proofing resists moisture vapor but not liquid water under pressure. Waterproofing resists liquid water under hydrostatic head. For any basement, foundation, plaza, or planter — anywhere groundwater or trapped surface water can develop head against the assembly — waterproofing is the code-required design.
Design fees are quoted as a percentage of the waterproofing trade cost or as a fixed lump sum by phase — investigation, basis-of-design, construction documents, and construction administration. We quote the fee before design begins, not after.
Yes. On a mid-life plaza deck or below-grade assembly, a targeted existing-condition assessment often produces the honest go/no-go answer — repair-in-place vs. full replacement — before design fees are committed. Fixed-fee, two to four weeks.
ACE Building Envelope Design has practiced envelope engineering across the Western United States on hundreds of commercial, multifamily, institutional, and legal-defense projects. Our senior engineers are licensed Professional Engineers, active in FGIA and ASTM committees, and have provided expert testimony in state and federal envelope-defect matters.
Founded and led by Conor Meyers (CEO), with John Harris (President) and Jedidiah Brandman (SVP) directing the technical practice.
ACE covers our Wasatch Front practice from our Western U.S. base, and related work in this market is documented at Waterproofing Consulting — Provo. Every engagement starts with a fixed-fee scope proposal — you see the price and fee before you commit.
Fill out the form below and we'll get back to you within 24 hours.
We've received your request and will be in touch within 24 hours.
